How We Repair Your Hobart Utensil Washer
Dishwashers fill, heat, spray and drain water using an inlet valve, a circulation pump, a drain pump, a heater and a control board.
Hobart Utensil Washer models often use model-specific control boards, sensors and diagnostic modes. We look up your exact model number so the right part goes in the first time.
Common Utensil Washer Problems We Fix
Not filling
A failed water inlet valve, a float switch stuck up or a closed supply valve.
Not drying
A burned-out heating element, a failed fan or no rinse aid.
Will not start
A door latch switch, a control board or a tripped thermal fuse.
Not draining
A clogged filter or drain hose, a blocked garbage disposal connection or a failed drain pump.
Dishes not clean
A dirty filter, clogged spray arms, low water temperature or a weak circulation pump.
Leaking
A worn door gasket, a loose hose clamp, a cracked tub or a failing pump seal.
Quick Checks Before You Call
These are safe for most owners and sometimes solve the problem without a visit:
- Clean the filter at the bottom of the tub.
- Run the kitchen tap hot before starting a cycle.
- Make sure the disposal knockout plug was removed if one was installed recently.
- Check the float in the front corner moves freely.
Still not working? Call (844) 442-1500 or try our troubleshooting wizard.
Our 5-Step Repair Process
- Call or book onlineTell us what your Hobart utensil washer is doing and when it started. We schedule the first available visit.
- DiagnosisThe technician checks power, controls and the parts most likely to fail, using the model's service data and test modes.
- Upfront quoteYou get the cause, the repair and the price before any work starts. If repair does not make sense, we tell you.
- RepairWe install original or equivalent parts matched to your model and clean up when we are done.
- Test and warrantyWe run the appliance through a full cycle to confirm the fix. The repair is covered by our 90-day parts and labor warranty.
Parts We Replace Most Often
- Drain pump
- Circulation pump and motor
- Water inlet valve
- Heating element
- Door latch
- Door gasket
- Control board
- Spray arms
Cost and Lifespan
Most utensil washer repairs cost $150–$400 including parts and labor, and these appliances typically last 9–12 years. These are national estimates: your exact price comes after the diagnosis. Use the repair vs replace calculator to compare.
Keep It Running Longer
- Run a cleaning cycle monthly, more often with hard water
- Clean the filter monthly
- Use rinse aid
Utensil Washer Repair in Daleville, VA
We repair utensil washers in Daleville (ZIP code 24083) and in nearby communities including Troutville, Blue Ridge and Fincastle. Hot, humid summers and cold winters in Virginia mean Daleville appliances deal with both extremes every year.
Frequently Asked Questions
How much does Hobart Utensil Washer Repair cost in Daleville, VA?
Most utensil washer repairs fall between $150–$400 including parts and labor. The final price depends on the part that failed and your model. You get an exact quote after the diagnosis and before any work starts.
Can you repair my utensil washer today?
Same-day visits depend on technician availability in Daleville. Call (844) 442-1500 early in the day for the best chance of a same-day or next-day appointment.
Is the repair guaranteed?
Yes. Parts and labor are covered by our 90-day warranty. If the same problem comes back within that time, we return and fix it.
Do you work on all Hobart models?
We repair current and older Hobart models. Some discontinued parts can be hard to find; if that is the case for your model, we tell you before you pay for a repair.
Should I repair or replace my utensil washer?
A utensil washer typically lasts about 9 to 12 years. If yours is well inside that range and the repair costs less than half the price of a new one, repairing usually makes sense. Near the end of its life, or when the repair costs more than half of a replacement, replacing is often the better value. We give you an honest opinion either way.